Engine CI / CC Liters Cyl. Years Vin Code / Engine Model Description Forging numbers Wt. Part # CON ROD PART #
ACURA                  
1590cc 1.6 4 86-87 D16A1 Integra. Flywheel flange has six bolt holes. Neck diameter is .865".   36 80013  
1.6 4 88-89 D16A1 Integra. Flywheel flange has six bolt holes. Neck diameter is .944".   32 80014  
1.6 4 88-89 D16A1 Integra. Flywheel flange has eight bolt holes. Neck diameter is 1.102".   36 80015  
1678cc 1.7 4 92-93 B17A1 DOHC, Integra GS-R, Vigor, V-TEC engine.   38 80016  
1797cc 1.8 4 94-01 B18C1, B18C5 DOHC. Integra GS-R 94-01, R Type 97-01, V-TEC engine.   38 80017  
1834cc 1.8 4 90-01 B18A1, B18B1 Integra - Except GS-R and V-TEC.   36 80018  
2156cc 2.2 4 97 F22B1 CL - Crankshaft has a 16mm bolt hole in neck.   38 80019  
2456cc 2.5 5 92-94 G25A1 Vigor.   38 80020  
2.5 5 95-98 G25A4     38 80020  
2675cc 2.7 V6 87-90 C27A1 For engines with housing bore of 2.7165" and 14mm bolt hole in neck. Legend.   35 80021  
3165cc 3.2 V6 96-97 6VD1 Isuzu engine used in SLX. Remove reluctor ring from old unit and install on new unit   37 92031  
3206cc 3.2 V6 91-95 C32A1 Legend.   40 80022  
3.2 V6 96-98 C32A6 TL.   40 80022  
3494cc 3.5 V6 98-99 6VE1 Isuzu engine used in SLX. Remove reluctor ring from old unit and install on new unit   40 92032  
AMERICAN MOTORS / JEEP / WILLYS          
134   4 39-73   Willys engine with straight dowel pin holes in the flywheel flange. Must specify if cam is chain driven rather than gear driven. 638121, 641127, 646318 53 64003 NA
  4 39-73   Willys engine with tapered dowel pin holes in flywheel flange. Must specify if cam is chain driven rather than gear driven. 638121, 641127, 646318 53 64001 NA
150 2.5 4 83-86 B, U Length of neck is 2 1/2" long. 3239611, 3239811 38 39022 804 (Rod Casting #351)
806 (Rod Casting #544, 641)
2.5 4 87-90 E, H, Z Length of neck is approximately 2 inches. 8933002904 40 39024 806
2.5 4 91-02 P Length of neck is approximately 2 inches. 8933002904 40 39025 806
151 2.5 4 80-83 B GM manufactured engine. 684, 777 30 18049 318
173 2.8 V6 83-84 X, Z GM manufactured engine with 2.494" mains. 504 48 18039 360
2.8 V6 85-86 W GM manufactured engine with 2.648" mains. 174, 216, 481, 817 48 18055 360
225 3.7 V6 02-09 K   53020967AB 46 19097 437
232 3.8 6 65-73   With flat flywheel flange. 3172216, 3172218R, 3188947, 31889117 68 39012 803
3.8 6 72-79   With centering ring on flywheel flange. 3214722 68 39013 805
242 4.0 6 87-90     3003453 62 39021 804  ('87-'89)
806  ('90)
4.0 6 91-02     53010411, 53020767 62 39026 806
258 4.2 6 72-86 A, C With centering ring on flywheel flange. Neck length is approximately 2 1/2". RD67703, 3214723, 3235477 75 39015 805
4.2 6 87-90 C Neck length is approximately 2". 3727 48 39023 805
287 4.7 V8 99-09 C Remove reluctor ring from old unit and install on new unit. This crankshaft kit fits applications for rod bearings with locating tabs. 53020683 55 19087 447
304 5.0 V8 70-71   With flat flywheel flange. 3195292, 3214724, 4487237 55 39018 810
5.0 V8 72-99   With centering ring on flywheel flange. 3195292, 3214724, 4487237 55 39019 810
318 5.2 V8 92-98   Chrysler Engine, standard transmission. 2658393, 3462387, 3751841 58 19052 423
5.2 V8 92-98   Chrysler Engine, automatic transmission. 2658393, 3462387, 3751841 58 19053 423
360 5.9 V8 70-71 N With flat flywheel flange. 3195292, 3214724, 4487237 55 39018 810
5.9 V8 72-99 N With centering ring on flywheel flange. 3195292, 3214724, 4487237 55 39019 810
5.9 V8 96-98 Z Grand Cherokee - Chrysler Engine, standard transmission 3418640, 4027169 66 19050 417  ('71-'91)
423  ('92-'03)
5.9 V8 96-98 Z Chrysler Engine, automatic transmission. 3418640, 4027169 66 19051 417  ('71-'91)
423  ('92-'03)
CHRYSLER / JEEP (Jeep see also American Motors)        
86 1.4 4 77-84   1410cc Mitsubishi G12B engine. G1 25 99064 NA
89 1.5 4 85-88 K 1468cc Mitsubishi G15B engine. Rod journal width is approximately 7/8" (.870"). G1 25 99070 NA
1.5 4 87-94 A, X 1468cc Mitsubishi 4G15 engine. Rod journal width is approximately 3/4" (.787"). G1, T1 25 99071 NA
97 1.6 4 71-88   Mitsubishi G32 engine. Timing gear fits flush to number one main journal. Neck has two keyways. Pilot hole adapter for automatic transmission is not furnished.   35 65003  
1.6 4 71-88   Mitsubishi G32 engine. Crankshaft has step between timing gear and number one main journal. Neck has two keyways. Pilot hole adapter for automatic transmission is not furnished.   35 65004  
1.6 4 89-90 Y, Z Mitsubishi 4G61 DOHC engine.   38 99093 NA
107 1.8 4 89-94   1755cc Mitsubishi 4G37 engine with five bolt holes in the flywheel flange.   38 99094 NA
1.8 4 92-02   1834cc Mitsubishi 4G93 engine with seven bolt holes in the flywheel flange. G93, 29, 31, 36 29 99095 NA
121 2.0 4 79-82 5, U 1995cc Mitsubishi G52B engine. Main diameter is 2.362". G52 47 99072A 413
2.0 4 85-92 D, R, U & V Mitsubishi G63B SOHC engine. Neck length is 1 1/2". Flywheel flange has six bolt holes. GE, 64 38 99085 NA
2.0 4 92-97   Mitsubishi 4G63 engine using flanged thrust bearing. Flywheel flange has seven bolt holes. Main thrust width located on number three main is 1.005". On 1997 verify thrust type.   35 99086 NA
2.0 4 97-99 F Mitsubishi 4G63 engine. Turbo application using thrust washers. Flywheel flange has seven bolt holes. Main thrust width located on number three main is 1.005". On 1997 verify thust type.   35 99086T  
2.0 4 95 C Flywheel flange has eight bolt holes. Crankshaft has a reluctor ring machined into the front counter-weight. 4556721, 4557665, 4667755 37 19092 NA
2.0 4 96-02 C, Y Flywheel flange has eight bolt holes. The crankshaft has a reluctor ring machined into the front counter-weight. 4556721, 4557665, 4667755 37 19090 NA
2.0 4 03-05   This crankshaft has a bolt-on reluctor ring on the rear counterweight.Remove reluctor ring from old unit and istall on new unit. AA, 04884106 37 19093  
135 2.2 4 81-85 B, C, D & E Flywheel flange has six bolt holes. Will not fit Dakota truck with standard shift transmission. 5214738 37 19067 414
2.2 4 86-88 C, D & E Flywheel flange has eight bolt holes. Neck diameter is .905" or approximately 7/8". Will not fit Dakota truck with standard shift transmission. 5214738, 5214990 37 19077 411  (Rod Casting # 4323218L)
416  (Rod Casting # 4323649)
414  (Rod Casting # 5203385)
2.2 4 87-88 A Inter-cooled turbocharger. Steel crankshaft with neck diameter of .905". 4323814, 43292355 44 19081 411  (Rod Casting # 4323218L)
416  (Rod Casting # 4323649)
414  (Rod Casting # 5203385)
2.2 4 89-94   Non turbo engine. Neck diameter us 1.003". Flywheel flange has eight bolt holes. 4448493 37 19078 411  (Rod Casting # 4323218L)
416  (Rod Casting # 4323649)
414  (Rod Casting # 5203385)
2.2 4 89   Turbo engine with steel crankshaft. Neck diameter of 1.003" 25585 44 19082 411  (Rod Casting # 4323218L)
416  (Rod Casting # 4323649)
414  (Rod Casting # 5203385)
148 2.4 4 85-88   Mitsubishi G64B engine. Main thrust width is 1.145" and located on number three main journal. 64 38 99089 NA
2.4 4 93-05   Mitsubishi 4G64 engine. Main thrust width is 1.005" and located on number three main journal. Rod thrust width is 1.050". Main bearing set comes with flanged main bearing. AT1, K 35 99088 NA
2.4 4 93-05   Mitsubishi 4G64 engine. Main thrust width is 1.005" and located on number three main journal. Rod thrust width is 1.050". Main bearing set comes with thrust washers. AT1, K 35 99088T  
2.4 4 95-02 B & X DOHC, eight bolt hole flange. Crankshaft has notches cut in the number two counter-weight for electronic ignition. Non turbocharged engines only. 4621916 43 19096 NA
2.4 4 03-08   Crankshaft has a bolt on reluctor ring located at the rear main. Remove reluctor ring from old unit and install on new unit. Non turbocharged engines only. 04781590AA 44 19098  
153 2.5 4 86-88 K Neck diameter is .866" or approximately 7/8". 4273232 39 19068 411  (Rod Casting # 4323218L)
416  (Rod Casting # 4323649)
414  (Rod Casting # 5203385)
2.5 4 89-95 G & J Crankshaft fits both turbo and non turbo engines. Neck diameter is 1.003" or approximately 1". Front of number one main has three bolt holes for timing gear. 448176, 486176, 4483176, 4448486, 4448490 39 19069 411  (Rod Casting # 4323218L)
416  (Rod Casting # 4323649)
414  (Rod Casting # 5203385)
2.5 4 91-02 P Dakota truck. 448176, 486176, 4483176, 4448486, 4448490 40 19070 411  (Rod Casting # 4323218L)
416  (Rod Casting # 4323649)
414  (Rod Casting # 5203385)
2.5 V6 95-02 H & N 2497cc Mitsubishi 6G73 engine. T3A, T3D, T3F, T3G, T3L, 09N, 19N, 29, 72, 76, 79 34 99073 403
156 2.6 4 79-94 D, E, G, H Mitsubishi G54B engine. Main journal diameter is 2.362". FWD G54 49 99072A 413
2.6 4 79-94 D ,E, G, H Mistubishi G54B engine. Main journal diameter is 2.362". RWD G54 49 99072B 413
167 2.7 V6 98-06 R, U & V DOHC engine. J 41 19086 428
181 3.0 V6 87-05 3, H & S Mitsubishi 6G72 engine. Cast iron crankshaft. T3A, T3D, T3F, T3G, T3L, 09N, 19N, 29, 72, 76, 79 34 99073 403
3.0 V6 91-96   Mitsubishi 6G72 engine with turbocharger. Forged steel crankshaft. E1, TDC, 72, 72P1 37 99075 NA
195 3.2 V6 98-03 J 24 Valve, SOHC, 60 degree Interference engine. A1D, B1A, 74K1,94062803G4   19088 NA
201 3.3 V6 90-06 3, G, R, T & U   3654, 4483654 43 19076 421
215 3.5 V6 93-97 F & G 300M, SOHC, cast iron block. A1D, B1A, 74K1,94062803G4 45 19091
3.5 V6 98-06 G, K & M 300M, SOHC, Aluminum block. A1D, B1A, 74K1,94062803G4 45 19095
3.5 V6 07-10 G, K & M SOHC, Aluminum block. A1D, B1A, 74K1,94062803G4 45 19099  
225 3.7 6 60-67   Centering ring diameter is 1 31/32". 284935, 2128492, 2264479 77 19019 405
3.7 6 68-78   Steel crankshaft with centering ring diameter of 2 5/32" and rod journal width of 1.225". 284935, 2128492, 2264479 77 19055 405
3.7 6 77-78   cast crankshaft with 1" rod journal diameter 3698966 81 19056 410
3.7 6 75-87   Cast iron crankshaft with rod journal width of 1.000". 359886, 3698966, 4095246 78 19058 410
3.7 V6 02-09 K   53020957AB 46 19097 437
232 3.8 V6 91-09 L   6433, 4556433 48 19089 430  ('91-'93)
432  ('94-'09)
239 3.9 V6 87-05 M & X Rod thrust width is .885". Standard drive transmission requires pilot bushing. 4323738, 4323769 44 19075 420  ('86-'91)
426  ('92-'03)
287 4.7 V8 99-09 N Remove reluctor ring from old unit and install on new unit. This crankshaft kit fits applications for rod bearings with locating tabs. 53020683 55 19087 447
318 5.2 V8 62-79   Steel crankshaft. 2128278, 2128869, 2268119, 2465747, 2532457, 2658278, 2843868 64 19044 415
5.2 V8 76-04   Cast iron crankshaft, standard transmission. 2658393, 2991345, 3462378, 3751841, 3751887 58 19052 417  ('71-'91)
423  ('92-'03)
5.2 V8 76-04   Cast iron crankshaft, automatic transmission. 2658393, 2991345, 3462378, 3751841, 3751887 58 19053 417  ('71-'91)
423  ('92-'03)
340   V8 68-73   Steel crankshaft. 2128278, 2128869, 2268119, 2465747, 2532457, 2658278, 2843868 64 19060 417
345 5.7 V8 03-08 D Hemi engine. Nose length 3.790" 53021300AA 59 19094 435
345 5.7 V8 09-10 D Hemi engine. Nose length 3.320" 3000BC 59 19100
360 5.9 V8 71-03   Standard drive transmission requires pilot bushing. 3418640, 4027169 66 19050 417  ('71-'91)
423  ('92-'03)
5.9 V8 71-03   Automatic transmission 3418640, 4027169 66 19051 417  ('71-'91)
423  ('92-'03)
361 5.9 V8 62-78   Steel crankshaft. Flywheel flange has a centering ring and six threaded bolt holes. Verify transmission type - Auto or Std. 2206159 74 19028 418
5.9 V8 74-78   Cast iron crankshaft. Flywheel flange has six threaded bolt holes. 3462923, 3751877, 4027172 70 19063 418
383   V8 61-71   Steel crankshaft. Flywheel flange has a centering ring and six threaded bolt holes. Verify transmission type - Auto or Std. 2206159 74 19028 418
  V8 70-71   Cast iron crankshaft. Flywheel flange has six threaded bolt holes. 3462923, 3751877, 4027172 70 19063 418
400 6.6 V8 72-80   Cast iron crankshaft. Flywheel flange has six threaded bolt holes. 3462923, 3751877, 4027172 70 19063 418
413   V8 62-77   Steel crankshaft. Flywheel flange has a centering ring and six threaded bolt holes. Verify transmission type - Auto or Std. 2206160 74 19046 419
440 7.2 V8 64-72   Steel crankshaft. Flywheel flange has a centering ring and six threaded bolt holes. Verify transmission type - Auto or Std. 2206160 74 19046 419
7.2 V8 73-80   Cast iron crankshaft. 3698461, 3751888, 4027175-3 78 19065 419
488 8.0 V10 92-03 W Truck engine. 53005823, 53006840 82 19085 423
FORD                  
81 1.3 4 88-92 K 1324cc Mazda B3 engine. Neck diameter is .865". A301, B301, 301 23 93038 NA
1.3 4 92-97 H 1324cc Mazda B3 engine. Neck diameter is 1.062". A301, B301, 301 23 93039 NA
98 1.6 4 71-73   Flywheel flange does not have a centering ring. This application is for Automotive ONLY. For Bobcat application 711MAD, 771MAC, 771MAE, 2731E, 2737E 32 25059 625
1.6 4 81-83   Year model is from 1981 to April of 1983. Front seal surface is 3/4" wide. E1EE-AB, E3EE-AB, E3EE-AA 30 25060 626
1.6 4 83-86   Year model is from May of 1983 to 1986. Front seal surface is 9/16" wide. E4EE-AA, E3EE-AA 30 25065 626
1.6 4 87-90   Mazda B6 SOHC engine. Year model is 1987 to October 1990. Neck length is 7/8" with a diameter of .865". B630, B616 25 93037 NA
1.6 4 91-95   Mazda B6 DOHC engine. Neck length is approximately 1 1/4" long with a diameter of 1.063". B6S7, B61K, B616 25 93046 NA
110 1.8 4 72-78   1796cc Mazda engine. 290 48 93032 NA
1.8 4 90-93   1839cc BP Mazda engine. Neck size is .865". BP01 28 93030 NA
1.8 4 94-96   1839cc BP Mazda engine. Neck size is 1.063". B630, BP02, G6 28 93041 NA
116 1.9 4 85-86   Rod journal size is 1.886". E5EE-BA 30 25067 626
1.9 4 87-99   Rod journal size is 1.728". E7EE-BB, FOEE-CC 30 25071 629
121 2.0 4 71-74 X 2000cc. 70HM-AKA, 72HM-JA 28 25047  
2.0 4 79-82   2000cc Mazda engine. 3975 48 93033 NA
2.0 4 82-88 C   E2ZE-BA, E43E-AC, 1D, 2D 48 25066 644
2.0 4 93-05 3 ZTEC DOHC engine. 933N-R67, 938M-R67, 938M-R68 34 25097 NA
2.0 4 93-99   1993cc FS Mazda engine. FS07, 15 37 93031 NA
2.0 4 97-05 P SOHC, SPI engine. RFF7CE-AA 32 25096 629
133 2.2 4 89-92   2184cc F2 Mazda engine. F201 34 93035 NA
140 2.3 4 74-81 A, B, T, W & Y 2300cc engine with two piece rear oil seal. 1D 40 25048 644
2.3 4 81-90 A, D, T, W & Z 2300cc engine with one piece rear oil seal. Single spark plug head engine. E2ZE-BA, E43E-AC, 1D, 2D 40 25066 644
2.3 4 84-94 R & X 2300cc HSC engine. E43EAB, E43AEC, E43GEAC 31 25068 648  (Wide Tang)
649  (Narrow Tang)
2.3 4 89-00 M 2300cc dual spark plug head engine. Main journal diameter is 2.205". C-GS, E89E-AB, 2D 48 25081 644
2.3 4 01-06 D, H DOHC, Duratec engine. This crankshaft does not have a gear for balance shaft. RF1L5G 35 25101 623
2.3 4 03-09 Z DOHC, Duratec engine. This crankshaft has a gear for balance shaft. Escape, Milan, Focus ZX3 3L5G6303DA   25100 623
153 2.5 4 86-91 D HSC engine. E63A-AA 30 25074 650
2.5 V6 93-96 B Mazda KL engine. Steel crankshaft with large center counterweight. KL01 43 93045S NA
2.5 V6 97-02   Mazda KL engine. Cast iron crankshaft with small center counterweight. KL07 37 93045 NA
2.5 V6 95-02 L Duratec engine. F53E-6303-AB, 5019934 39 25095 614
2.5 4 98-01 C OHC Engine. RFF87E-AC 39 25082 NA
171 2.8 V6 74-75   Flanged main bearing packed in kit. 74TM-AA, 76TM-AA, 78TM-AA, 78TM-CA, 82TM-HAA 36 25050 651
2.8 V6 76-79   Thrust washers packed in kit. 74TM-AA, 76TM-AA, 78TM-AA, 78TM-CA, 82TM-HAA 36 25050 651
2.8 V6 80-86   Flanged main bearing packed in kit. 74TM-AA, 76TM-AA, 78TM-AA, 78TM-CA, 82TM-HAA 36 25049 651
177 2.9 V6 86-90   To 5/10/90 86TM6303BA, 88TM6303BA, 91TM6303AA 36 25051 651
2.9 V6 90-92   From 5/10/90 86TM6303BA, 88TM6303BA, 91TM6303AA 36 25052 651
183 3.0 V6 86-94 U   RF-E6AE-AH 38 25075 652
3.0 V6 95-08 U   RF-F58E-6303AA 40 25076 652
3.0 V6 93-95 W Nissan VG30E engine. Neck has two keyways and a diameter of .985".   38 94044 NA
3.0 V6 96-99 W Nissan VG30E engine. Neck has two keyways and a diameter of 1.262".   38 94048 NA
3.0 V6 96-05 S 2966cc Duratec DOHC engine. F53E-6303-AB, 5019934 39 25095 614
3.0 V6 89-95 Y Yamaha engine.   37 25099 NA
195 3.2 V6 93-95 P Yamaha engine.   37 25099 NA
200 3.3 6 65-83   Crankshaft has seven main journals. 1H, 3H, 1HA, E1BE-BB 47 25026 602  ('70-'77)
603  ('78-'83)
3.3 6 81-83   With pep or pen trans 5/16" centering ring 3H   25061 603
201 3.3 V6 99-02 T Nissan VG33E engine.     94048 NA
232 3.8 V6 82-83   Engine has two piece rear oil seal. E2AE-DB 36 25069 604
3.8 V6 83-95   Engine has one piece rear oil seal and front main journal width is 1.312". Rear wheel drive. N2AE-AF, N3AE-AA 36 25070 604
3.8 V6 01-05     1F2E 38 25070L  
3.8 V6 88-95   Front main journal width of 1.390" and rod bearing width of .666". Non supercharged engine only. Front wheel drive. E2AE-A, E3AE-AA, E3DE-BB, E9DE-BB, F68EB-A 36 25083 604
3.8 V6 89-95 R Supercharged engine only. E9TE 46 25085 NA
3.8 V6 96-00   Rod bearing width of .784". Non supercharged engine only. Front wheel drive. F4SZ6303AX, F6ZZ6303AX, F68EAB 36 25090 606
240 3.9 6 65-75     1L, 1LA, 1LAB 60 25027 607
3.9 V6 01-07 6   RF4F2EAA 38 25102  
244 4.0 V6 90-95   Neck has 3/8" long keyway and flywheel flange has six bolt holes. C94HA, 90TM6303AA, 90TM6303AB 43 25053 653
4.0 V6 95-96   Neck has 1 1/4" long keyway and flywheel flange has six bolt holes. C94HA, 96TM6303AA 47 25087 653
4.0 V6 97-98 E Neck has 1 1/4" long keyway and flywheel flange has eight bolt holes. OHV Engine C94HA, XL2E6303AA, 96TM6303AA, 97JM6303AA 47 25088 653
4.0 V6 97-09   8-Bolt flywheel flange SOHC, light weight piston. X3ZE-BA, XL2E   25077 653
250 4.1 6 69-81 C & L   C9DE-A, 2H, 2HA, 2HAB 65 25038 608  ('69-'77)
609  ('78-'80)
255 4.2 V8 80-82 D   1J, 2J 43 25062 631
256 4.2 V6 97-07 2 4196cc engine. RFF65EAC, RFF85EAC 46 25089  
272   V8 55-58     EC 60 25004 NA
281 4.6 V8 91-07 W Romeo engine. Flywheel flange has six bolt holes and kit is packed with one flanged bearing and one thrust washer.  This may replace a two flanged bearing main set.MS2007P/5M2007P F1AE-AD, F65E6303BB, RFF1AE6303AD 50 25084 NA
4.6 V8 93-01 V Steel crankshaft is fully counterweighted and flywheel flange has eight bolt holes. MS2198AL F8TECE 50 25098S  
4.6 V8 96-04 X & 6 Windsor engine, flywheel flange has six bolt holes.  Kit is packed with three thrust washers.5M7296A/MS2202P F65EBB18D, F65E6303BB 50 25092 646
4.6 V8 96-01 X & 6 Windsor engine, flywheel flange has eight bolt holes and kit is packed with one flanged bearing and one thrust washer. MS2007P/5M2007P RFF1AE6303AD, F65EBB18D, F65E6303BB 50 25093 646
4.6 V8 96-07 X & 6 Windsor engine, flywheel flange has eight bolt holes and kit is packed with three thrust washers. Main set MS2202p/5M7296A RFF1AE6303AD, F65EBB18D, F65E6303BB 50 25098  
4.6 V8 02-05 W SOHC, aluminum block. Flywheel flange has six bolt holes and kit is packed with one flanged bearing and one thrust washer. Main set MS2198AL/.MS2259A RFF65E6303BC 50 25086 NA
289   V8 63-68     C2OZ, C3AE-N, C3OZ, 1M, 3M 43 25022 NA
292   V8 55-66   Passenger car application, cast iron casting. EC 60 25004 NA
300 4.9 6 65-82 B, E, Y, Z & 9 With oil slinger C5TE-F, C6TE-G, 1N, 1NA, 1NABC, 2N, 2NA, 2NABC 76 25029  
4.9 6 82-99   Without oil slinger 1N, 1NA, 2NABC 76 25073 612  ('82)
613  ('83-'93)
302 5.0 V8 68-80   Except for 78-79 Lincoln Versailles. 2C, 2M, 2MA, DOZE-A 45 25039 631
5.0 V8 81-82   Crankshaft is equipped with a slinger at the rear seal surface for engines with two piece rear oil seal. E1AE-AA, 2MAE 43 25063 631
5.0 V8 83-00   Crankshaft does not have a slinger and is for engines with a one piece rear oil seal. E7AE-AA, 2MAE 43 25064 631
330 5.4 V8 66-72   For heavy duty applications. Neck diameter is 1.750". C4TE-A, C6TE-B, C7TE-A, DOTE-A, D2TE-A 78 25031 637
5.4 V8 64-78   Medium duty applications. Pilot hole is .750" deep. Neck diameter is 1.375". COAE-B, C3AE-A, C4AE-A, C5AE-A, EDD, 2T, 2TA 68 25030 632
5.4 V8 97-08 L,A,L 5398cc Triton engine. SOHC  XL3E-BA, F75-E, F75-1E, F75EAE 52 25094 656
351 5.8 V8 70-74   Cleveland engine. 4M, 4MA 63 25043 636
5.8 V8 75-82   Modified engine. 1K, 1KA, 8M 63 25042 638
5.8 V8 69-83   Windsor engine with two piece rear oil seal. 69-75 uses main set 5M981P / MS981P. Specify year when ordering. 3M, 3MA, 7M, 7MA 60 25040 635
5.8 V8 83-98   Windsor engine with one piece rear oil seal. E4AE-BA, 7M, 7MA 60 25072 635
352   V8 58-67   Pilot hole is .750" deep. COAE-B, C3AE-A, C4AE-A, C5AE-A, EDD, 2T, 2TA 68 25030 632
359 5.9 V8 73-78   Truck and heavy duty application, steel casting. C4TE-A, C6TE-B, C7TE-A, DOTE-A, D2TE-A 78 25031 637
360 5.9 V8 68-78   Pilot hole is .750" deep. COAE-B, C3AE-A, C4AE-A, C5AE-A, EDD, 2T, 2TA 68 25030 632
361 5.9 V8 64-78   Truck and heavy duty application, steel casting. C4TE-A, C6TE-B, C7TE-A, DOTE-A, D2TE-A 78 25031 637
363 6.0 V8 03-10 P 32V Turbo. International Power-Stroke VT365 Diesel     42832  
370 6.1 V8 79-94     1V, 1VA, 1VAB 85 25055 429
389 6.4 V8 73-78   1 3/4" Pulley snout diameter C4TE-B, C6TE-C, C7TE-B, C7TE-EA, D2TE-EA 78 25032 637
390 6.4 V8 61-76   1 3/8" Pulley snout diameter C1AE-A, C1AE-D, C2AE-D, C3AE-B, C3AE-C, C3AE-D, C3AE-E, C4AE-B, 2U, 2UA, 3U 71 25036 637
391 6.4 V8 64-78   1 3/4 " Pulley snout diameter C4TE-B, C6TE-C, C7TE-B, C7TE-EA, D2TE-EA 78 25032 637
400 6.6 V8 71-82 S & Z   5M, 5MA, 5MAB, 5MABC 68 25041 638
401 6.6 V8 59-79   Truck engine. Rod journal diameter is 2.710". C1TE-B, C2TE-A 94 25033 677
415 6.8 V10 97-13 S, Y 6751cc Triton engine.   67 25091 656
421 6.9 V8 83-87   International Navistar diesel truck engine. 1803420C1, 1805420C1 88 42830 620
427   V8 63-68   1 3/8" Pulley snout diameter C1AE-A, C1AE-D, C2AE-D, C3AE-B, C3AE-C, C3AE-D, C3AE-E, C4AE-B, 2U, 2UA, 3U 71 25036 637
429 7.0 V8 79-95   Neck diameter is 1.750". D9TE-AA, D9TE6303BA 79 25079 429
445 7.3 V8 88-94 C, K & M International Navistar diesel truck engine. 1803420C1, 1805420C1 88 42830 620
7.3 V8 94-03 F International Navistar Power Stroke diesel truck engine. 1818200C2, 1818200C3, 1831140C1 88 42831 620
460 7.5 V8 68-78 A, C & J   C8VE-A, 2Y, 2YA, 2YAB, 2YABC 84 25057 641
7.5 V8 79-83 G & L Crankshaft has rear oil slinger. 3Y, 3YA, 3YB 84 25058 642
7.5 V8 84-98 G & L Crankshaft does not have a rear oil slinger. 3Y, 3YA, 3YB 84 25080 642  ('84-93)
643  ('94-'98)
475 7.8 V8 58-79   Rod journal diameter is 2.710". C1TE-B, C2TE-A 94 25033 677
477 7.8 V8 58-81   Rod journal diameter is 2.710". C1TE-B, C2TE-A 94 25033 677
534 8.8 V8 58-81   Truck engine. Rod journal diameter is 2.710". C1TE-C, C2TE-B 110 25034 677
GENERAL MOTORS              
61 1.0 3 85-01   993cc Suzuki G10 engine. K 17 95055 NA
81 1.3 4 95-01   1324cc Suzuki G13A and G13BA engines. 43 18 95057 NA
92 1.5 4 85-87   1471cc Isuzu 4XC1 and 4XC1T engines. Flywheel flange has six bolt holes. KN7, KN8, KN9, 4127, 5330 22 92024 NA
1.5 4 87-89   1471cc Isuzu 4XC1 and 4XC1T engines. Flywheel flange has eight bolt holes. KN, KN7, KN10, 73 22 92023 NA
98 1.6 4 76-87     1140N 40 18057 340
1.6 4 76-87     7184N 40 18044 340
1.6 4 85-98   Toyota 4ALC and 4AFE engines. Flywheel flange has six bolt holes. 1AC, 3A, 4AC, 4AFE, 4ALC, 5A 19 96060 NA
1.6 4 85-95   Toyota engine. Flywheel flange has eight bolt holes. Rod journal diameter is 1.574". E2, G2, O1, P3, Q5, 6 30 96061 NA
1.6 4 88-92   Toyota 4AGE engine. Rod journal diameter is 1.653". Flywheel flange has eight bolt holes. E2, E5 30 96062 NA
1.6 4 89-04   Suzuki G16, G16KC, G16KV engines. OK, X20, 119 30 95054 NA
1.6 4 90-93   Isuzu 4XE1 engine. Rod journal diameter is 1.572" and main journal diameter is 2.044". KN2, KN5, KN7 22 92025 NA
110 1.8 4 76-82   Neck has 2 keyways. Flywheel flange has six bolt holes.   40 92028 NA
1.8 4 93-97   1762cc Toyota 7AFE engine. Geo Prism.   32 96085 NA
1.8 4 98-08 8 1794cc Toyota 1ZZFE engine. Geo Prism and Pontiac Vibe.   34 96086  
1.8 4 01-06 L 1796cc Toyota 2ZZGE engine. Geo Prism and Pontiac Vibe.   31 96073  
112 1.8 4 1982 G Crankshaft has rear seal oil slinger. 8705N, 14018705 34 18050 350
1.8 4 82-86 J & O OHC engine. R90155143, R90156143 34 47029 320
119 1.9 4 82-85   Isuzu G200Z engine.   40 92028 NA
1.9 4 91-92     2100883, 210005833, 210008673 27 18090 NA
1.9 4 93-98     2100883, 210005833, 210008673 27 18091 119
1.9 4 98-04     2100757AA2, 210092355 35 18094 NA
121 2.0 4 82-84 B & P OHV engine with a two piece rear oil seal. 3278N, 14033278 34 18053 330
2.0 4 84-86 P OHV engine with a one piece rear oil seal. 3278N, 7243N, 7248N 34 18054 330  ('84)
331  ('85-'86)
2.0 4 87-89 I OHV engine with a reluctor ring for distributor-less ignition. L3, 003K, 003N, 900003C, 10103606 34 18063 333
2.0 4 87-91 K & M OHC engine. R9028036, R90280395, R960280399, 2670 40 47030 332
2.0 4 92-95 H OHC engine. Front counterweight has two protruding steel pins for electronic ignition and three bolt holes on top for detachable reluctor ring. 399, 2670, 90409507 40 47031 331
133 2.2 4 90-97 G & 4 OHV engine. L3, 1237, 4618 34 18079 333
2.2 4 98-04 H, 4 & 5 OHV engine. L3, 1237, 4618 34 18093 333N
2.2 4 00-06 F DOHC Ecotec engine. 7327 40 18095 NA
138 2.3 4 87-88 D Quad 4 engine. Notches on reluctor ring are approximately one inch from casting line down the center of crankshaft. Remove oil pump drive gear / sprocket from old unit and install on new unit. 22532120 40 41010 339
2.3 4 89-94 A, D & 3 Quad 4 engine. Notches on reluctor ring line up with the casting line down the center of crankshaft. Remove oil pump drive gear/sprocket from old unit and install on new unit. 22532120, 22545690, 22582120, 24574115 40 41011 339
2.3 4 95 D Dohc Quad 4 Remove oil pump drive sprocket from old unit and install on new unit. 24574115 40 41012 339
146 2.4 4 96-04 T 2392cc LD9 Quad 4 DOHC engine. Remove oil pump drive gear/sprocket from old unit and install on new unit. 4620 50 41013 341
151 2.5 4 80-85 R Pilot insert in the flange end of the crankshaft determines A, B, or C part number. 684 30 18048 318
2.5 4 79-84 R Bushing not included 684, 777 30 18049  
2.5 4 85-86 E & R Bushing not included 017, 684, 777 30 18065 318
2.5 4 85-86 U Bushing not included 771 30 18064 318
2.5 4 87-88 E & R Crankshaft has a reluctor ring for distributorless ignition. Bushing not included 381, 405, 543 30 18066 319
2.5 4 88-93 A, E & R Crankshaft has a reluctor ring and a 78 tooth oil pump/balancer drive gear. Overall length of crankshaft is 21 3/4". Bushing not included 405, 540, 543 34 18068 319
2.5 4 88-93 U Crankshaft has a reluctor ring and a 78 tooth oil pump/balancer drive gear. Overall length of crankshaft is 20 1/2". Bushing not included 406, 540 34 18076 319
153   4 62-70   May be used in some marine applications. 8522, 3788522, 379082N, 5743014 40 18040 NA
173 2.8 V6 80-85 Z, 1 & 7 First design engine with small main block. Main journal diameter is 2.494". 264, 504 48 18039 360
2.8 V6 85-87 B, R, S, W & X Second design engine with large main block. Main journal diameter is 2.648". This crankshaft used in externally balanced engine. 85, 174, 196, 817 48 18055 360
2.8 V6 87-89 S & W Crankshaft has a reluctor ring with notches for use in a distributorless internally balanced engine. 481, 526 40 18073 361
2.8 V6 87-93 R Used in a distributor type internally balanced engine. 526 40 18072 361
181 3.0 4 74-93   Marine application used in Mercruiser and OMC engines with a two piece rear oil seal. N393775, N398776, N9341352 44 18098 261M
3.0 4 94-99   Marine application used in Mercruiser and OMC engines with a one piece rear oil seal. Rod thrust width is 1.035". N14094623, 14096624 54 18099 261M
3.0 4 94-99   Marine application used in Mercruiser and OMC engines with a one piece rear oil seal. Rod thrust width is 0.963".   54 18096  
3.0 V6 82-85 E Early engine with tall deck block and long connecting rods. 257, 404 40 14024 211
3.0 V6 85-88 L Late engine with short deck block and short connecting rods. 377, 732, 819 40 14027 212
3.0 V6 97-02 R Crankshaft has bolt on reluctor ring attached to the rear counterweight. 1255069, 90499243 41 18097  
191 3.1 V6 88-05 D Crankshaft has a reluctor ring without notches for use in a distributor type engine. 981 40 18080 361
3.1 V6 88-05 J, M, T & V Crankshaft has a reluctor ring with notches for use in a distributorless engine. 17, 268, 981, 1X-148071 40 18077 361
194   6 62-67     3788424, 3820618N 55 18017 200
196 3.2 V6 78-80     229, 877, 1255674, 1257125, 1260877 40 14022 201
200 3.3 V6 78-79     726N, 1354N 42 18038 370
204 3.3 V6 89-90 N Flywheel flange has six bolt holes. 694 33 14029 214
3.3 V6 91-94 N Flywheel flange has eight bolt holes. 817, 4817, 25534817 34 14030 214
207 3.4 V6 91-05 E, S & X LA1, LQ1, L32 engines.  Crankshaft has a reluctor ring with notches for use in a distributorless engine.  17, 268, 981, 1X-148071 40 18077 361
3.4 6 05-09   24x reluctor 64 42 18009  
  3.5   04-09 LX9 84mm stroke 261   18010  
217 3.6   08-10   LLT 0689   18004  
220 3.6 6 04-09 LY7 Cadillac CTS SRX     18002  
225 3.7 V6 64-67 B Buick engine. 1255646, 1255845, 1357898, 1378351, 1378354 40 14020 208
229 3.8 V6 80-84   Chevrolet engine. 726N, 1354N 42 18038 370
230 3.8 6 62-70   Chevrolet engine. 3788424, 3820618N 55 18017 200
231 3.8 V6 64-77 C Odd firing engine. 1255646, 1255845, 1357898, 1378351, 1378354 40 14020 208
3.8 V6 77-87 A, 3 & 8 Application is for rear wheel drive vehicles with the exception of the front wheel drive Riviera and Toronado with conventional mount engines. 229, 877, 1255674, 1257125, 1260877 40 14022 201  ('79-'80)
210  ('81-'89)
3.8 V6 84-88 B & 3 Front wheel drive vehicles with transverse mount engine. 267 40 14025 210
3.8 V6 89-90 C This engine is equipped with a cam driven balancer shaft. Flywheel flange has six bolt holes. 113, 502 40 14028 201  (Rod Casting # 673)
210  (Rod Casting # 763)
215  (Rod Casting # 918)
216  (Rod Casting # 742)
217  (Rod Casting # 359)
218  (Rod Casting # 669)
3.8 V6 90-93 L, C & 1 Series I engine. Flywheel flange has eight bolt holes. 309, 737, 4737 37 14031 201  (Rod Casting # 673)
210  (Rod Casting # 763)
215  (Rod Casting # 918)
216  (Rod Casting # 742)
217  (Rod Casting # 359)
218  (Rod Casting # 669)
3.8 V6 94 L & 1 Series I engine. Flywheel flange has eight bolt holes. 309, 737, 4737 37 14032 201  (Rod Casting # 673)
210  (Rod Casting # 763)
215  (Rod Casting # 918)
216  (Rod Casting # 742)
217  (Rod Casting # 359)
218  (Rod Casting # 669)
3.8 V6 95 C Series I engine. Flywheel flange has eight bolt holes. 309, 737, 4737 37 14033 201  (Rod Casting # 673)
210  (Rod Casting # 763)
215  (Rod Casting # 918)
216  (Rod Casting # 742)
217  (Rod Casting # 359)
218  (Rod Casting # 669)
3.8 V6 95-05 K, L & 1 Series II engine. 2170 36 14034 201  (Rod Casting # 673)
210  (Rod Casting # 763)
215  (Rod Casting # 918)
216  (Rod Casting # 742)
217  (Rod Casting # 359)
218  (Rod Casting # 669)
235   6 53-55   Crankshaft is packed with dowel-type main bearings. 3701488 86 18003 NA
  6 55-63   Crankshaft is packed with locking lip type main bearings. (Dowel type on lower half and locking lip on top half). 3701488 86 18005 NA
244 4.0 V8 00-08   3995cc engine with 14mm bolt hole in neck. 12554681 47 15019 279
250 4.1 6 66-76 D & Q Neck diameter is 1.250" and is not tapped. 407N, 460407, 3876802N 72 18028 200
4.1 6 77-84     460407 72 18045 200
252 4.1 V6 80-84   Application is for rear wheel drive vehicles with the exception of the front wheel drive Riviera and Toronado with conventional mount engines. 229, 877, 1255674, 1257125, 1260877 40 14022 210
4.1 V8 82-91   Conventional mount engine with three bolt holes in the flywheel flange of the crankshaft. 1617590 45 15012 252
4.1 V8 84-91   Transverse mount engine with six bolt holes in the flywheel flange of the crankshaft. 1617590, 1629091, 1646737, 1648455 45 15013 252
256 4.2 6 99-05 S Flywheel flange bolt holes are 10mm X 1.5.& 10mm X 1.0 Customer needs to match bolt pitch. 209, 866, 998 80 18018  
4.2 6 06-07 S Flywheel flange bolt holes are 10mm X 1.5.& 10mm X 1.0 Customer needs to match bolt pitch. 139 80 18020  
4.2 6 08-09   60-2 teeth on the timing wheel     18019  
260   V8 75-76   Automatic transmission 393654   41020 300
  V8 75-82 F   230376, 388766, 393654, 418882, 556607 52 41025 301
261   6 53-55   Crankshaft is packed with dowel-type main bearings. 3701488 86 18003 NA
  6 55-62   Crankshaft is packed with locking lip type main bearings. (Dowel type on lower half and locking lip on top half). 3701488 86 18005 NA
262 4.3 V6 84-86 N For engines with two piece rear oil seal. 1174, 14071174 40 18059 262  (Rod Casting w/ Dimple)
263  (Rod Casting # 818)
264  (Rod Casting # 045)
4.3 V6 86-99 Z Heavy crankshaft used in all engines without balance shaft and in all VIN code Z with heavy piston and pin assemblies (745 grams). This crankshaft has two kwyways. 480, 640, 865, 5480, 5865, 8640, 10055480, 10105865, 14088640 45 18060 262  (Rod Casting w/ Dimple)
263  (Rod Casting # 818)
264  (Rod Casting # 045)
4.3 V6 86-99 W, X & Z Lightweight crankshafts used in 1992-99 VIN code W engine, some 1995 VIN code Z engine and the 1996-99 VIN code X engine have light piston and pin assemblies (675 grams). This crankshaft has a single keyway. 480, 685, 5480, 10055480, 10105865 45 18074 262  (Rod Casting w/ Dimple)
263  (Rod Casting # 818)
264  (Rod Casting # 045)
4.3 V6 98-05   Crankshaft has a deep pilot hole depth of 1.410". Balance holes drilled in both the front and rear rod journal. RPO-ZK3 or ZN4 engines. 255 45 18085 262  (Rod Casting w/ Dimple)
263  (Rod Casting # 818)
264  (Rod Casting # 045)
265 4.3 V8 55-63   Chevrolet engine. 3727449, 3734627, 3735236, 3815822, 3836266, 3876764 54 18007 265
4.3 V8 80-81 S Pontiac engine. 525887 45 47027 318
4.3 V8 94-96 W L99 engine. 10168568   18082 269
273 4.5 V8 88-92   Conventional mount engine with three bolt holes in the flywheel flange of the crankshaft. 1617590 45 15012 252
4.5 V8 88-92 3, 5 & 8 Transverse mount engine with six bolt holes in the flywheel flange of the crankshaft. 1617590, 1629091, 1646737, 1648455 45 15016 253
278 4.6 V8 93-99 Y & 9 Cadillac LD8 and L37 Northstar engine with 18mm bolt hole in neck. 3525774, 3544669 46 15018 279
4.6 V8 00-08 Y & 9 Cadillac LD8 and L37 Northstar engine with 14mm bolt hole in neck. 12554681 46 15019 279
283   V8 55-63   Chevrolet engine. 3727449, 3734627, 3735236, 3815822, 3836266, 3876764 54 18007 280
  V8 66-67   Cherolet engine. 4849847 54 18006 280
  V8 64-67   Chevrolet engine. 3849847, 3876768 54 18008 280
292 4.8 6 60-66   Flywheel flange has 7/16" bolt holes and one dowel pin hole. 3884653 71 18023 292
4.8 6 67-90   Flywheel flange has 1/2" bolt holes and three dowel pin holes. 0363, 2774220N, 3299990, 3910363 71 18027 292
293 4.8 V8 99-05 V GEN III truck engine. For use in engines with rear flange width of .857" (7/8"). A new ignition reluctor ring is installed on the crankshaft. 12553482, 482 55 18087 NA
300 4.9 V8 91-95 B Cadillac engine. 3520090 48 15017 NA
301 4.9 V8 77-81 T, W & Y Pontiac engine. 525887 45 47027 318
305 5.0 V8 76-85 G, H & U Chevrolet engine, early model application with two piece rear oil seal. 3932442 59 18061 260
5.0 V8 86-04 E, F, G, H & M Chevrolet engine, late model application with one piece rear oil seal. 14088526, 14088535, 14088995 59 18056 260  (Forged)
261  (Powdered Metal)
307 5.0 V8 68-75   Chevrolet engine. 1130, 4672, 3911001, 3911001A, 3941174 56 18031 260
5.0 V8 80-90 Y & 9 Oldsmobile engine. 230376, 388766, 393654, 418882, 556607 52 41028 301  ('80-'84)
302  ('85-'89)
325 5.3 V8 99-06 B, C, M, P, T, Z GEN III truck engine with rear flange width of .857" (7/8"). A new ignition reluctor ring is installed on the crankshaft. 12552216 55 18088 268
5.3 V8 07-up U GEN III LQ4, LQ9, Vortec 6000 truck engine with aluminun heads and a rear flange width of .857 (7/8"). 58 tooth reluctor. 12552216 55 18001 268
326   V8 67-75   Pontiac engine. 481397, 9773382, 9773383, 9783785, 9783786, 9793573 74 47019 316
327   V8 62-67   Chevrolet small journal engine with forged steel crankshaft. 2680. 4577, 3782680 56 18013 280
  V8 68-74   Chevrolet large journal engine with cast iron crankshaft. 1130, 4672, 3911001, 3911001A, 3941174 56 18031 260
  V8 65-67   Turbo-Hydramatic transmission without tapped nose. 4577 56 18024 280
340   V8 66-67   Buick engine. 1235419, 1260718, 1261119, 1275809, 1378346 57 14018 204E
346 5.7 V8 97-05 G, S GEN III engine with aluminum block and heads with a rear flange width of .857" (7/8"). A new ignition reluctor ring is installed on the crankshaft. 12552216, 12555089 55 18088 268
5.7 V8 07-up U GEN III LQ4, LQ9, Vortec 6000 truck engine with aluminun heads and a rear flange width of .857 (7/8"). 58 tooth reluctor. 12552216 55 18001 268
350 5.7 V8 67-85   Chevrolet engine. Heavy duty forged steel crankshaft and two piece rear oil seal. 1182, 2690 59 18033S 260
5.7 V8 68-76   Automatic transmission. Except Toronado & El Dorado 393654   41020 300
5.7 V8 68-80 R Oldsmobile engine. 230376, 388766, 393654, 418882, 556607 52 41028 301
5.7 V8 68-81 H, J & X Buick engine. 1235419, 1260718, 1261119, 1275809, 1378346 57 14018 204E  ('66-'72)
204  ('73-'78)
5.7 V8 68-85 L Chevrolet engine. 310514, 3932442 59 18033 260
5.7 V8 67-75 M & P Pontiac engine with outside diameter of centering ring of 2.750". 4813, 481379, 481380, 496452 70 47019 316
5.7 V8 75-80 M & P Pontiac engine with outside diameter of centering ring of 2.490". 4813, 496452 70 47028 316
5.7 V8 86-01 J Chevrolet engine. Heavy duty forged steel crankshaft with one piece rear oil seal. 14088532 59 18075 260  (Forged)
261  (Powdered Metal)
5.7 V8 86-95 R Chevrolet engine. Late model with one piece rear oil seal. 14088526, 14088535, 14088995 59 18062 260  (Forged)
261  (Powdered Metal)
5.7 V8 92-97 P LT1 engine with one piece rear oil seal. 14088526, 14088535, 14088995 59 18078  
5.7 V8 96-05   Vortec engine with one piece rear oil seal. 14088526, 14088535, 14088995 59 18056 260
365 6.0 V8 1999 U GEN III LQ4 Vortec 6000 truck engine with cast iron cylinder heads and a rear flange width of 1.250" (1 1/4"). A new ignition reluctor ring is installed on the crankshaft. 12552215 55 18083 NA
6.0 V8 00-05 U GEN III LQ4, LQ9, Vortec 6000 truck engine with aluminun heads and a rear flange width of .857 (7/8"). A new ignition reluctor ring is installed on the crankshaft. 12552216 55 18088 268
6.0 V8 07-up U GEN III LQ4, LQ9, Vortec 6000 truck engine with aluminun heads and a rear flange width of .857 (7/8"). 58 tooth reluctor. 12552216 55 18001 268
6.0 V8 05-06 LS2 GEN IV engine with aluminum block and heads with a rear flange width of .857" (7/8"). A new ignition reluctor ring is installed on the crankshaft. 12552216, 12555089 55 18088 268
366 6.0 V8 66-90   Steel crankshaft with a two piece rear oil seal. 6223, 7115, 9115 72 18026 203
6.0 V8 65-75   Chevrolet engine. Passenger car and light duty truck cast iron crankshaft with a two piece rear oil seal. 6223, 7115, 9115, 3874874, 3863144, 3904815 72 18035 203
6.0 V8 91-98   Cast iron crankshaft with a one piece rear oil seal. 10114187 71 18041 203
6.0 V8 91-98   Steel crankshaft with a one piece rear oil seal. 10114189 71 18041S 203
368 6.0 V8 80-84 6 & 9 Cadillac engine. Check forging number for identification. 1609142 67 15011 NA
376 6.2 V8 07-UP LS2 GEN III LQ9 vortec rear flange .857 7/8" 58 tooth reluctor 12552216 55 18001 268
381 6.2 V8 82-91   Diesel engine with two piece rear oil seal. 14024236, 23500245 80 44830 379
383   V8     This is a special aftermarket application by grinding a 400 Chevrolet crankshaft to fit a 350 engine block. Customer must have a 400 Chevrolet crankshaft core for exchange. 3882841, 3951528, 3951529 59 18000  
395 6.5 V8 92-94   Diesel engine with one piece rear oil seal. 23502592 80 44831 379
6.5 V8 92-02   Diesel engine with one piece rear oil seal. Fits both turbo and non turbo engines. 23502592 80 44831 379
396   V8 65-75   Chevrolet engine. Passenger car and light duty truck cast iron crankshaft with a two piece rear oil seal. 6223, 7115, 9115, 3874874, 3863144, 3904815 72 18035 203
  V8 65-70   Chevrolet engine. Heavy duty steel forging crankshaft with two piece rear oil seal. 6223, 7115, 9115, 3874874, 3863144, 3904815 72 18026 203
400   V8 67-75   Pontiac engine with outside diameter of centering ring of 2.750". 4813, 481379, 481380, 496452 70 47019 316
6.6 V8 70-80   Chevrolet small block 400 engine. 3882841, 3951528, 3951529 58 18034 400
  V8 75-80   Pontiac engine with outside diameter of centering ring of 2.490". 4813, 496452 70 47028 316
402   V8 70-75   Chevrolet engine with heavy duty forged steel crankshaft. 6223, 7115, 9115 72 18026 203
403 6.6   01-06   6.6 Liter, Duramax Diesel.   78 18092  
403   V8 77-79 K Oldsmobile engine. 418882, 556607 52 41029 307
425 7.0 V8 77-79 S & T Cadillac engine. Check forging number for identification. 1609142 67 15014 NA
427   V8 64-85   Chevrolet engine. Passenger car and light duty truck cast iron crankshaft. 6223, 7115, 9115, 387474, 3863144, 3904815 72 18035 203
  V8 64-90   Chevrolet heavy duty steel forging with a two piece rear oil seal. 6223, 7115, 9115 72 18026 203
  V8 91-98   Cast iron crankshaft with a one piece rear oil seal. 10114187 71 18041 203
  V8 91-03   Steel forged crankshaft with a one piece rear oil seal. 10114189 71 18041S 203
429   v8 64-67   Cadillac     15020  
430   V8 67-69   Buick engine. 1379242 74 14019 206
454 7.4 V8 70-90   Chevrolet engine. Passenger car and light duty truck cast iron crankshaft with a two piece rear oil seal. 3521, 7416, N353039, 3875945, 3963524, 3967463 74 18036 203
7.4 V8 70-90   Chevrolet engine. Heavy duty steel forging with a two piece rear oil seal. 3521, 7416 74 18036S 203
7.4 V8 91-00   One piece rear oil seal. 10114188 74 18042 203
7.4 V8 91-01   Chevrolet engine with heavy duty steel forging for engines with a one piece rear oil seal. 14097044 74 18042S 203
455   V8 68-76   Oldsmobile engine. 230377, 230378, 397363, 400943 77 41022 303
  V8 70-78 P, W, X & Y Pontiac engine. 496453, 9799103 80 47024 316
  V8 70-76 B Buick engine. 1379242 74 14019 206
472   V8 68-74 R Cadillac engine. 1486424 86 15009 254
496 8.1 V8 01-06 G 8100 L18 Vortec truck engine. 430 85 18089  
500   V8 70-76   Cadillac engine. 1495094, 1495095, 1496793 82 15010 254
HONDA                  
1488cc 1.5 4 76-83 ED, EC, EM1     22 80003  
1.5 4 84-87 EW1, EW3-4, D15A2-3 84-87 Civic 1500, 85-87 CRX Si & Civic Si, 84-87 CRX DX   25 80010  
1.5 4 84-87 D15A1 Rod journal size 1.653", main journal size 1.771". Neck diameter is .865"   23 80012  
1493cc 1.5 4 88-95 D15B1-8 D15Z 88-95 Civic, 88-91 CRX, 92-95 del SOL & V-TEC. Rod journal diameter 1.653", main journal diameter 1.771". Neck diameter is .944".   28 80023  
1.5 4 88-95 D15B1-8 D15Z 88-95 Civic, 88-91 CRX, 92-95 del SOL & V-TEC. Rod journal diameter 1.653", main journal diameter 1.771". Neck diameter is .865".   28 80024  
1.5 4 90 D15B1 Rod journal diameter 1.496", main journal diameter 1.771". Neck diameter is .944".   25 80026  
1590cc 1.6 4 88-95 D16A6, D16Z6 88-91 Civic Si & CRX Si, 92-95 Civic & del SOL Si. Rod journal diameter 1.771", main journal diameter 2.165". Neck diameter is .865".   32 80013  
1.6 4 88-00 D16A6, D16Z6, D16Y5, D16Y7, D16Y8 88-91 Civic Si & CRX Si, 92-95 Civic & del SOL Si, 96-00 Civic, del SOL S, Civic EX V-TEC, del SOL Si, Civic HX. Rod journal diameter 1.771", main journal diameter 2.165". Neck diameter is .944"   32 80014  
1595cc 1.6 4 94-00 B16A2, B16A3 94-00 Del Sol V-TEC, 96-00 Civic Si   34 80027  
1599cc 1.6 4 76-78 EF, EG 76-78 Accord   22 80004  
1751cc 1.8 4 79-81 EK 79-81 Accord, 81 Prelude. Flywheel flange diameter is 2.913" with 10mm bolt holes.   35 80006  
1.8 4 81-83 EK, EK1 81-83 Accord, 81-82 Prelude. Flywheel flange diameter is 2.992" with six 12mm bolt holes.   35 80005  
1829cc 1.8 4 83-87 ES1-3, ET2, A18A1 83-87 Prelude, 84-85 Accord & Accord Sei, 11.5 mm bolt hole in the neck. Flywheel flange has eight 12mm bolt holes.   35 80007  
1955cc 2.0 4 86-89 BS, BT, A20A1-3 86-89 Accord & 86-87 Prelude . 11.5 mm bolt hole in neck   35 80007  
2.0 4 86-89 BS, BT, A20A1-3 86-89 Accord & 86-87 Prelude. 14mm bolt hole in neck   34 80028  
1958cc 2.0 4 88-90 B20A3 88-90 Prelude SOHC engine. Rod journal diameter 1.771", main journal diameter 2.165".   40 80029  
2.0 4 88-91 B20A5 88-91 Prelude DOHC engine. Rod journal diameter 1.889", main journal diameter 2.165" 13mm bolt hole in neck.   38 80009  
2.0 4 88-91 B20A5 88-91 Prelude DOHC engine. Rod journal diameter 1.889", main journal diameter 2.165". 11mm bolt hole in neck.   38 80030  
2056cc 2.0 4 90-91 B21A1 90-91 Prelude. 13mm bolt hole in neck   38 80009  
2.0 4 90-91 B21A1 90-91 Prelude. 11mm bolt hole in neck   38 80030  
2156cc 2.2 4 90-93 F22A1-4, F22A6 90-93 Accord, 91-93 Accord SE. 14mm bolt hole in neck. Stroke 3.74"   38 80008  
2.2 4 92-97 F22A1, F22B1-2, F22B6 92-96 Prelude S, 95-97 Odyssey, 94-97 Accord, Accord V-TEC. 16mm bolt hole in neck.   38 80019  
2157cc 2.2 4 93-96 H22A1 93-96 Prelude V-TEC. Rod journal diameter 1.889", main journal diameter 1.9685". Stroke 3.57".   42 80025  
2259cc 2.3 4 92-93 H23A1 Prelude Si, 14mm bolt hole in neck. Mains 1.968" Rod 1.889" stroke 3.74"   38 80008  
2559cc 2.6 4 94-96 4ZE1 Isuzu Engine.   42 92027 NA
2.6 4 95-02 4ZE1 Isuzu Engine. Remove reluctor ring off of old unit and install on new unit.     92029 NA
2675cc 2.7 V6 87-97 C27A1 C27A4 For engines with housing bore of 2.7165".  May require 14mm bolt.   35 80021  
3165cc 3.2 V6 94-95 6VD1 94-95 Passport.   37 92030 NA
3.2 V6 96-02 6VD1 6VD1W Remove reluctor ring from old unit and install on new unit.   37 92031 NA
3494cc 3.5 V6 98-04 6VE1 DOHC engine. Remove reluctor ring from old unit and replace on new unit.   40 92032  
3638cc 3.5 V6 06-10 YF1, J35A9 SOHC VTEC, Pilot, Ridgeline     80031  
HYUNDAI                
1468cc 1.5 4 86-89 G4AJ Excel. Rod journal width is .870". G1 25 99070 NA
1.5 4 90-94 G4DJ Excel, Scoupe. Rod journal width is .787". G1,T1 25 99071 NA
1495cc 1.5 4 93 G4EK 93 Scoupe. Front seal surface diameter is 1.377". Neck is machined flat on two sides. D5 27 65020  
1.5 4 94-95 G4EK 94-95 Scoupe. Front seal surface diameter is 1.377".   27 65021  
1.5 4 95-00 G4EK 95-00 Accent. This shaft equipped with reluctor ring for distributorless ignitions.   28 65022  
1595cc 1.6 4 92-95 G4CR 92-95 Elantra.   38 99092  
1795cc 1.8 4 96-98 G4GM 96-98 Elantra, Tiburon. Centering ring of flywheel is 1.612" in diameter. Flange thickness is .818". Shaft has a bolt-on reluctor ring. B1.8 38 99090  
1.8 4 96-98 G4GM 96-98 Elantra, Tiburon. Centering ring of flywheel is 1.378" in diameter. Flange thickness is .715". Shaft has a bolt-on reluctor ring. B1.8 38 99091  
1836cc 1.8 4 93-95 G4CN 93-95 Elantra.   38 99085 NA
1975cc 2.0 4 97-02 G4GF 97-'02 Elantra, Tiburon - Centering ring of flywheel is 1.612" in diameter. Flange thickness is .818". Shaft has bolt-on reluctor ring. B2.0 38 99090  
2.0 4 97-02 G4GF 97-02 Elantra, Tiburon. Centering ring of flywheel is 1.378" in diameter. Flange thickness is .715". Shaft has bolt-on reluctor ring. B2.0 38 99091  
1997cc 2.0 4 92-03 G4CP 92-03 Sonata. Engine code "F".   38 99085 NA
2350cc 2.4 4 89-91 G4CS 89-91 Sonata. VIN Code "S". 64 38 99089 NA
2.4 4 99-05 G4JS 99-05 Sonata, 01-04 Santa Fe   41 99088T  
2.4 4 06-10 G6KB, G4KC   824 38 99097  
2493cc 2.5 V6 99-01 V, G6BV Sonata.     99096  
2656cc 2.7 V6 01-06 G6BA Santa Fe, Sonata, Tiburon, Tucson.     99096  
2972cc 3.0 V6 90-98 G6AT 90-98 Sonata.   34 99073 NA
3489cc 3.5 V6 02-05 E, G6CU XG350.     99077  
INFINITI                  
1998cc 2.0 4 91-02 SR20DE 91-00 G20. 60J40, 43-D 40 94054  
2960cc 3.0 V6 90-92 VG30E 90-92 M30.   38 94044  
3.0 V6 93-'97 VG30DE 93-97 J30. 30P43 38 94048  
3.0 V6 96-01 VQ30DE 96-00 I30. 31U40 38 94063  
4494cc 4.5 V8 90-96 VH45DE 90-96 Infinity Q45. 60U41 52 94064  
ISUZU                  
1471cc 1.5 4 85-89 4XC1, 4XC1T Flywheel flange has six bolt-holes. (See also 12670). 4127, 5330, KN7, KN10 22 92024 NA
1.5 4 87-89 4XC1, 4XC1T I-Mark Turbo. Flywheel flange has eight bolt-holes. (See also 12550). 73, KN, KN7, KN10 22 92023 NA
1588cc 1.6 4 1989 4XE1W I-Mark. Main journal diameter is 1.887". 73, KN, KN7, KN10 22 92023 NA
1.6 4 90-93 4XE1, 4XE1W Stylus, Impulse, Impulse Turbo. Main journal diameter is 2.044". KN2, KN5, KN7 22 92025 NA
1817cc 1.8 4 81-85 G180Z I-Mark, Pickup.   40 92028 NA
1949cc 1.9 4 83-87 G200, G200Z Trooper II, Impulse, Pickup.   40 92028 NA
1994cc 2.0 4 85-89 4ZC1 Impulse turbo.   32 92034 NA
2156cc 2.1 4 96-97 RJ1 Oasis. F22 Honda engine. 16mm snout bolt   38 80019  
2195cc 2.2 4 96-97 LN2 Hombre. GM engine. Parting edge of crankshaft is approximately 1/2" away from notch on the reluctor ring. This part number will not interchange with 12970. 1237, L3, 4618 34 18079 333
2.2 4 98-00 LN2 Hombre. GM engine. Parting edge of crankshaft lines up next to notch on the reluctor ring. This part number will not interchange with 12740. 1237, L3, 4618 34 18093 333N
2198cc 2.2 4 98-03 X22SE DOHC Engine. Daewoo W/ balance gear 2671, 90530454, 93242486 48 92022 NA
2254cc 2.3 4 86-95 4ZD1 86-95 Pickup, 86-87 Trooper II, 89-93 Amigo, 88-89 Impulse. AB 40 92026 NA
2559cc 2.6 4 88-94 4ZE1 Pickup, Trooper II, Amigo, Rodeo.   42 92027 NA
2.6 4 95-97 4ZE1 Pickup, Trooper II, Amigo, Rodeo. Crankshaft has a bolt-on sensor ring at the rear main journal.   42 92029 NA
2827cc 2.8 V6 89-92   Trooper II. GM engine. 481, 526 40 18073 361
3135cc 3.1 V6 91-94 CPC Pickup, Rodeo. GM engine. 981 40 18077 361
3165cc 3.2 V6 92-95 6VD1 Trooper, Rodeo.7-Notch wheel   40 92030 NA
3.2 V6 96-97 6VD1 96-97 1/2 Trooper, Rodeo. Remove reluctor ring from old unit and install on new unit.   40 92031 NA
3.2 V6 98-02 6VD1W 97 1/2-02 Amigo, Rodeo. Remove reluctor ring from old unit and install on new unit.   40 92031 NA
3494cc 3.5 V6 98-04 6VE1 98-02 Trooper - DOHC - VIN code "X". Remove reluctor ring from old unit and install on new unit.   40 92032  
JEEP / AMERICAN MOTORS / WILLYS          
134   4 39-73   Willys engine with straight dowel pin holes in the flywheel flange. Must specify if cam is chain driven rather than gear driven. 638121, 641127, 646318 53 64003 NA
  4 39-73   Willys engine with tapered dowel pin holes in flywheel flange. Must specify if cam is chain driven rather than gear driven. 638121, 641127, 646318 53 64001 NA
150 2.5 4 83-86 B, U Length of neck is 2 1/2" long. 3239611, 3239811 38 39022 804 (Rod Casting #351)
806 (Rod Casting #544, 641)
2.5 4 87-90 E, H, Z Length of neck is approximately 2 inches. 8933002904 40 39024 806
2.5 4 91-02 P Length of neck is approximately 2 inches. 8933002904 40 39025 806
151 2.5 4 80-83 B GM manufactured engine. 684, 777 30 18049 318
173 2.8 V6 83-84 X, Z GM manufactured engine with 2.494" mains. 504 48 18039 360
2.8 V6 85-86 W GM manufactured engine with 2.648" mains. 174, 216, 481, 817 48 18055 360
225 3.7 V6 02-09 K   53020967AB 46 19097 437
232 3.8 6 72-79   With centering ring on flywheel flange. 3214722 68 39013 805
242 4.0 6 87-90     3003453 62 39021 804  ('87-'89)
806  ('90)
4.0 6 91-95     53010411, 53020767 62 39026 806
4.0   96-02   Automatic Only 53010411 , 53020767 62 39027 806
258 4.2 6 72-86 A, C With centering ring on flywheel flange. Neck length is approximately 2 1/2" for engines with "V" type belts and pulleys. RD67703, 3214723, 3235477 75 39015 805
4.2 6 87-90 C Neck length is approximately 2" for engines with serpentine type belt and pulley. 3727 48 39023 805
287 4.7 V8 99-09 C Remove reluctor ring from old unit and install on new unit. This crankshaft kit fits applications for rod bearings with locating tabs. 53020683 55 19087 447
304 5.0 V8 70-71   With flat flywheel flange. 3195292, 3214724, 4487237 55 39018 810
5.0 V8 72-99   With centering ring on flywheel flange. 3195292, 3214724, 4487237 55 39019 810
318 5.2 V8 92-98   Chrysler Engine, standard transmission. 2658393, 3462387, 3751841 58 19052 417  ('71-'91)
423  ('92-'03)
5.2 V8 92-98   Chrysler Engine, automatic transmission. 2658393, 3462387, 3751841 58 19053 417  ('71-'91)
423  ('92-'03)
360 5.9 V8 70-71 N With flat flywheel flange. 3195292, 3214724, 4487237 55 39018 810
5.9 V8 72-99 N With centering ring on flywheel flange. 3195292, 3214724, 4487237 55 39019 810
5.9 V8 96-98 Z Grand Cherokee - Chrysler Engine, standard transmission. 3418640, 4027169 66 19050 417  ('71-'91)
423  ('92-'03)
5.9 V8 96-98 Z Chrysler Engine, automatic transmission. 3418640, 4027169 66 19051 417  ('71-'91)
423  ('92-'03)
KIA                  
1493cc 1.5 4 01-05 A5D Rio. A5 29 93050  
1597cc 1.6 4 94-97 B6 Sephia - Mazda engine. B6S7, B61K, B616 25 93046 NA
1793cc 1.8 4 98-04 T8 Sephia. Spectra     93049  
1839cc 1.8 4 95-97 BP Sephia 95-97. VIN code 5.   28 93041 NA
1998cc 2.0 4 95-09   Mazda engine used in Sportage. Crankshaft flange has 8 bolt-holes and 1 dowel pin hole. DOHC engines only. Use MS8133P FE50 32 93051  
2350cc 2.4 4 06-10 G6KB, G4KC   824 38 99097  
2493cc 2.5 V6 2001 G6BV Optima.     99096  
2656cc 2.7 V6 01-05 G6BA Optima.     99096  
3489cc 3.5 V6 02-06 G6CU Sedona, Sorento.     99077  
MAZDA                  
1489cc 1.5 4 95-98 Z5 Protégé. B3C7 23 93039  
1597cc 1.6 4 86-94 B6 323, Tracer SOHC engines. Neck approximately 7/8" long and .865" in diameter. B616, B630 25 93037 NA
1.6 4 88-93 B6 323 GT Turbo & DOHC engines. Neck approximately 1 3/4" long and .865" in diameter. B630XD 25 93048 NA
1.6 4 92-95 B6 MX3, Miata, 323. Neck approximately 1 1/4" long and 1.063" in diameter. B6S7, B616, B630, B61K 25 93046 NA
1.6 4 99-02 ZM 99-02 Protégé B6S7, B616, B630, B61K 25 93046 NA
1796cc 1.8 4 72-78 VB B1800 290 48 93032 NA
1839cc 1.8 4 90-93 BP05 Protégé - Neck diameter .865". BP01, 47, 48 28 93030 NA
1.8 4 94-05 BP05 Protégé 94-98, Miata 94-05. Neck diameter 1.063" 22, G6, G7, NP, BP02, B630 28 93041 NA
1844cc 1.8 V6 92-94 K8 MX3.   33 93047 NA
1970cc 2.0 4 79-84 MA B2000, 626. U975, 3975 40 93033 NA
1991cc 2.0 4 93-03 FS 626, MX6. 15, FS07 37 93031 NA
2.0 4 01-04   DOHC, ZETEC Engine. 01-02 626, 01-04 Tribute. 933M-R67, 938M-R67, 938M-R68 34 25097 NA
1998cc 2.0 4 83-87 FE 83-87 626, 85-87 B2000, 86-87 626 Turbo. Flywheel flange has six bolt holes. Crankshaft neck is approximately 1" in length. FE01, FE50 48 93034 NA
2184cc 2.2 4 87-99 F2 87-99 B2200, 88-92 626, 88-92 MX6. Also fits turbo. F201 34 93035 NA
2255cc 2.3 V6 95-06 KJ Millenia. Crankshaft has a tapered neck. E1, F6, JLKJ, KL01 43 93044 NA
2302cc 2.3 4 94-97 8A B2300, Ford engine. 2D, C-GS, E89E-AB 48 25081 644
  2.3 4 03-09 Z DOHC, Duratec engine. This crankshaft has a gear for balance shaft. Mazda 3, Mazda 6. 3L5G6303DA   25100 623
2497cc 2.5 V6 93-96 KL 626, MX6, Millenia. Steel crankshaft with large center counterweight. KL01 43 93045S NA
2.5 V6 97-02 KL KL engine. 626, Millenia. Cast iron crankshaft with small center counterweight. KL07 37 93045 NA
2555cc 2.6 4 87-88 AM1 B2600 - Mitsubishi G54B engine. G54 49 99072B 413
2606cc 2.6 4 89-94 G6 B2600i, MPV. G601 37 93036 NA
2954cc 3.0 V6 88-98   MPV , 929 This crankshaft has no oil pump drive   43 93043 NA
3.0 V6 88-98   MPV, 929. This crankshaft has a 0.660" wide oil pump drive block on the neck.   43 93042 NA
3.0 V6 88-98   MPV, 929. This crankshaft has a 0.500" wide oil pump drive block on the neck.   43 93040 NA
2967cc 3.0 V6 01-05   Ford Duratec - Tribute. F53E6303AB, 50119934 39 25095 614
2999cc 3.0 V6 94-99 8U B3000 - OHV Ford engine. RFE6AE-AH 38 25075 652
3996cc 4.0 V6 91-95 ZZL B4000 Navajo - Ford engine. 90TM6303AB 43 25053 653
MITSUBISHI                
1410cc 1.4 4 78-84 G12B   G1 25 99064 NA
1468cc 1.5 4 85-89 G15B, G4AJ 85-88 Mirage, 87-89 Precis, 86-89 Excel. Rod journal width is approximately .850 G1 25 99070 NA
1.5 4 89-00 G15B, 4G15, G4DJ 89-00 Mirage, 90-94 Excel. Rod journal width is approximately .790. Front seal surface diameter is 1.181". G1, T1 25 99071 NA
1595cc 1.6 4 89-95 4G61, G4CR 89 Turbo Mirage, 91-92 Mirage.   38 99093 NA
1597cc 1.6 4 85-88 G32B Crankshaft neck has two keyways and the timing gear fits flush to the # 1 main journal.   35 65003  
1.6 4 85-88 G32B Crankshaft neck has two keyways and the neck has a step between the timing gear and the # 1 main journal.   35 65004  
1755cc 1.8 4 89-94 4G37 Eclipse - The flywheel flange has five bolt-holes.   35 99094 NA
1.8 4 92 4G33 L300 Van - The flywheel flange has five bolt-holes.   35 99094 NA
1795cc 1.8 4 84-88 G62B, G4GM 5/84-88 Cordia & Tredia. Crankshaft neck length is approximately 1 1/2".   38 99085 NA
1834cc 1.8 4 92-02 4G93 92-94 Expo, 92-96 Mirage. G93 29 99095 NA
1997cc 2.0 4 84-92 G63B, 4G63, G4CN, G4CP 5/84-88 Cordia, Tredia, 5/84-89 Pickup, 89-92 Eclipse & Galant. Crankshaft neck length is approximately 1 1/2". Flywheel flange has six bolt holes. 64, GE 38 99085 NA
2.0 4 93-96 4G63 93-94 Galant, Eclipse - 93-96 Eclipse turbo - Flywheel flange has 7 bolt holes. Main bearing set comes with flanged main bearing.   35 99086 NA
2.0 4 95 420A Eclipse - Chrysler 16 valve, DOHC engine. Main bearings for 95 year model only. 4556721, 4557665, 4667755 37 19092 NA
2.0 4 96-99 420A Eclipse - Chrysler 16 valve, DOHC engine. 4556721, 4557665, 4667755 37 19090 NA
2.0 4 97-99 4G63 97-99 Turbo engines use thrust washers instead of flanged bearing. Crankshaft flange has seven bolt holes.   35 99086T  
2350cc 2.4 4 85-92 G64B, G4CS 85-88 Galant, 85-92 Van, 90-92 Pickup, 89-92 Expo. Thrust width on # 3 main is 1.145". 64 38 99089 NA
2.4 4 93-97 4G64, 4G64FR 95-96 Pickup, 95-97 Expo, Eclipse & Galant, Montero Sport. Thrust width on # 3 main is 1.005". Rod thrust width is 1.050". This kit packed with flanged main bearings. AT1, K 35 99088 NA
2.4 4 98-02 4G64 98-02 Galant & Eclipse. This kit is packed with thrust washers. AT1, K 35 99088T  
2555cc 2.6 4 79-89 G54B Montero, Pickup, Starion. G54 49 99072B 413
2972cc 3.0 V6 88-04  6G72 89-00 Montero & Pickup, 95-03 Montero Sport, 88-90 Galant Sigma, 92-99 Diamante, 90-95 Sonata, 91-99 3000GT. Cast iron crankshaft. VIN Codes H & P. T3A, T3D, T3F, T3G, T3L, 29, 72, 76, 79, 09N, 19N 34 99073 403
3.0 V6 91-99 6G72 91-99 3000 GT Turbo. Steel crankshaft 72, 1, P1, TDC 37 99075 NA
3496cc 3.5 V6 94-04 6G74, 6G74DN 94-02 Montero, 97-04 Montero Sport, 97-04 Diamante. Rod journal diameter is 2.165". 74K1, 94062803G4 44 99076 NA
NISSAN                  
1597cc 1.6 4 83-88 E16, EA16i 83-86 Sentra, 83-88 Pulsar. 31M 31 94040 NA
1.6 4 87 CA16DE 87 Pulsar SE. Flywheel flange has eight bolt holes. D4240 32 94055 NA
1.6 4 89-00 GA16i, GA16DE 89-00 Sentra, 91-94 NX, 89-90 Pulsar NX and 91-00 200SX. 4-0, 40-2, 77AS 29 94041 NA
1809cc 1.8 4 84-86 CA18ET 200SX Turbo. Flywheel flange has six bolt holes. D0242 32 94055 NA
1.8 4 88-89 CA18DE Pulsar SE. Flywheel flange has eight bolt holes. D4240 32 94056 NA
1952cc 2.0 4 74-79 L20B 74-79 Pickup, 200SX, 510, 610 and 710. U6040 45 94057 NA
2.0 4 80-86 Z20, Z20S, Z20E 80-81 510 and 200SX, 83-86 720 Pickup. U6040 45 94057 NA
1974cc 2.0 4 82-89 CA20S, CA20E 82-85 Stanza, 84-89 200SX, 84-89 Stanza Wagon, 86-89 Stanza Sedan. D1742, 57E40 35 94046 NA
1998cc 2.0 4 91-02 SR20DE 91-00 Sentra & 200SX, 91-94 NX. 43-D, 60J40 40 94054 NA
2187cc 2.2 4 81-83 Z22, Z22E 81-83 720 Pickup, 81-83 200SX. 06W, 21-0, 90 45 94047 NA
2389cc 2.4 4 83-90 Z24 83-90 720 Pickup, 86-90 Pathfinder, Van & D21 Pickup. 30W41, 30W42 45 94042 NA
2.4 4 89-04 KA24E, KA24DE 89-99 240SX, 89-98 Stanza & Axxess, 90-97 Pickup, 93-00 Altima, 98-04 Frontier & Xterra. Crankshaft neck has two keyways. Flywheel flange has no centering ring. 86G 39 94050 NA
2.4 4 89-04 KA24E, KA24DE 89-99 240SX, 89-98 Stanza & Axxess, 90-97 Pickup, 93-00 Altima, 98-04 Frontier & Xterra. Crankshaft neck has three keyways. Flywheel flange has no centering ring. 86G 39 94053 NA
2.4 4 89-04 KA24E, KA24DE 89-99 240SX, 89-98 Stanza & Axxess, 90-97 Pickup, 93-00 Altima, 98-04 Frontier & Xterra. Crankshaft neck has three keyways. Flywheel flange has a centering ring. 40F 39 94051 NA
2.4 4 89-04 KA24E, KA24DE 89-99 240SX, 89-98 Stanza & Axxess, 90-97 Pickup, 93-00 Altima, 98-04 Frontier & Xterra. Crankshaft neck has two keyways. Flywheel flange has a centering ring. 30R 39 94052 NA
2393cc 2.4 6 70-82 L24, L24E 70-73 240Z, 77-81 810, 81-6/82 Maxima. Rod journal diameter is 1.967". E3140, E3141, E3142 64 94058 NA
2.4 6 82-84 L24E 7/82-84 Maxima. Rod journal diameter is 1.770". W3140 64 94059 NA
2488cc 2.5 4 02-07 QR25DE Altima, Sentra. Must reuse reluctor rIng from old crankshaft. 3 bolt reluctor ring. AE040 36 94060  
2.5 4 02-07 QR25DE Altima, Sentra. Must reuse reluctor rIng from old crankshaft. 4 bolt reluctor ring. JA02H 36 94066  
2753cc 2.8 6 74-83 L28E, L28ET 280Z, 280ZX. P-3040 64 94061 NA
2960cc 3.0 V6 84-87 VG30i, VG30E, VG30ET 84-3/87 Maxima, 300ZX, 200ZX & Pickup, 84-87 300ZX Turbo. Neck has one keyway. 1181-36-4191 38 94043 NA
3.0 V6 87-95 VG30i, VG30E, VG30ET SOHC engines. 4/87-94 Maxima, 4/87-99 300ZX & 200SX, 84-89 300XZ Turbo, 93-95 Quest & Villager, 4/87-95 Pickup & Pathfinder. Neck has two keyways and is .985" in diameter.   38 94044 NA
3.0 V6 91-94 VG30DE DOHC engines. 91-94 Maxima. Crankshaft has three keyways in the neck and one bolt-on counterweight located in the middle of the crankshaft. Flywheel flange has eight bolt-holes. 30P43 39 94049 NA
3.0 V6 90-96 VG30DE VG30DETT 90-96 300ZX & 300ZX Turbo. Neck has two keyways and is 1.262" in diameter. Flywheel flange has eight bolt-holes. Shaft has one bolt-on counterweight located in the middle of the crankshaft. 30P43 38 94062 NA
3.0 V6 95-01 VQ30DE DOHC engines. 95-01 Maxima. 31U40 38 94063 NA
3.0 V6 96-99 VG30E 96-98 Quest - Also fits 96-99 Mercury Villager - Neck has two keyways and is 1.262" in diameter. Flywheel flange has six bolt-holes.   38 94048 NA
3275cc 3.3 V6 96-04 VG33E 96-02 Pathfinder, 99-02 Quest, 99-04 Frontier & Xterra.   38 94048 NA
3498cc 3.5 V6 01-06 VQ35DE 350Z 03-06, Altima 02-06, Maxima 02-06 and Murano 03-06.    4W041   94065  
SUBARU                
1820cc 1.8 4 93-96 EJ18E Impreza.   25 84000  
1999cc 2.0 4 02-05 EJ20T Rod diameter 2.046" thrust #5 main Turbo DOHC   25 84004  
2212cc 2.2 4 90-98 EJ22E Impreza, Legacy, Outback. #3 Thrust   25 84000  
2.2 4 99-UP EJ22E Rod diameter 2.046" #5 thrust.   25 84003  
2457cc 2.5 4 96-98 EJ25 96-99 Legacy, 98 Impreza & Forester. Rod diameter is 1.889 and the thrust is located on main three.   25 84001  
2458cc 2.5 4 99-07 EJ25I Impreza, Legacy, Forester. Rod diameter is 2.046" and main thrust is located in the number 5 position.   25 84002  
SUZUKI                  
993cc 1.0 3 80-94 G10 85-88 Swift, - Also used in some GM vehicles. K 17 95055 NA
1298cc 1.3 4 90-01 G13K, G13BB, G13BA 90-95 Samurai, 89-00 Swift. 043, 72, Y10 18 95057 NA
1324cc 1.3 4 86-89 G13A 86-89 Samurai, 89 Sidekick. 43 18 95052 NA
1590cc 1.6 4 89-02 G16KC, G16KV, G16B 89-98 Sidekick, 95-00 Esteem, 96-98 X90, 99-01 Vitara. 119, OK, X20 30 95054 NA
1995cc 2.0 4 99-05 J20A 99-03 Vitara, 04-05 Forenza. Verify 6 or multi-tooth reluctor ring.   44 95058  
1999cc 2.0 4 04-05 X2OSED, C2ONED 04-05 Forenza w/ Daewoo motor 2671, 608 48 92020  
2494cc 2.5 V6 99-05 H25A 99-05 Grand Vitara, DOHC V6 24valve engine. 86 40 95059  
2737cc 2.7 V6 01-07 H27A 01-05 XL7, 06-07 Grand Vitara. 86 40 95059  
TOYOTA                
1452cc   4 80-91 1AC, 3AC 80 thru 10/83. 1A, 3A, 4A, 5A 19 96060 NA
1456cc 1.5 4 87-94 3E, 3EE   3E 39 96075 NA
1497cc 1.5 4 92-98 5EFE 92-98 Paseo, 95-98 Tercel. 3E 39 96075 NA
1.5 4 00-05 1NZFE 00-05 Echo.     96095  
1587cc 1.6 4 83-88 4AC, 4ALC  Corolla. Flywheel flange has six bolt holes. 1A, 3A, 4A, 5A 19 96060 NA
1.6 4 85-87 4AGEC, 4AGELC 85-87 MR2, Corolla GTS. Flywheel flange has eight bolt holes. Rod journal diameter is 1.574".   30 96061 NA
1.6 4 88-91 4AGE, 4AGEC, 4AGELC 4AGZE 88-89 MR2, 88-91 Corolla GTS. Flywheel flange has eight bolt holes. Rod journal diameter is 1.653". E2, E5, D6 30 96062 NA
1.6 4 88-97 4AF, 4AFE 88-89 SR5, 88-97 Corolla, 90-92 Celica ST.   19 96060 NA
1762cc 1.8 4 93-97 7AFE 93-97 Corolla, 94-97 Celica.   32 96085 NA
1794cc 1.8 4 98-08 1ZZFE 98-08 Corolla, 00-06 Celica, MR2 and Matrix.   34 96086  
1796cc 1.8 4 00-06 2ZZGE 00-05 Celica, 05-06 Corolla XRS, 03-06 Matrix.   31 96073  
1995cc 2.0 4 83-86 2SELC 83-86 Camry, 85-86 Celica   40 96076 NA
1998cc 2.0 4 84-85 3YEC   3Y, Z21 34 96065 NA
2.0 4 86-89 3SGTE, 3SGELC 86-89 Celica GTS. Flywheel flange has eight 10mm bolt holes. Crankshaft rear seal diameter is 3.346". 3SF 40 96077 NA
2.0 4 87 3SFE Crankshaft rear seal size is 3.346". Flywheel flange has six bolt holes. 3SF 40 96079 NA
2.0 4 88-91 3SFE 88-91 Camry, '88-'89 Celica. Flywheel flange has eight bolt holes. 3SF 40 96077 NA
2.0 4 88-95 3SGTE 88-95 Celica Turbo, 90-95 MR2 turbo. Flywheel flange has eight 12mm bolt holes. Crankshaft rear seal size is 3.504". Steel crankshaft.   39 96072 NA
2.0 4 96-00 3SFE 96-00 Rav 4     96082 NA
2.0 4 01-03 1AZFE 01-03 Rav 4.   37 96088  
2164cc 2.2 4 90-01 5SFE 90-99 Celica and MR2, 92-00 Camry, 98-00 Solera. Remove counter balance gear from old unit and install on new unit. 1341103010-D 41 96081 NA
2.2 4 90-91 5SFE This crankshaft will not accommodate a counter balance gear.   41 96080 NA
2189cc 2.2 4 3/82-84-1/2 20R     43 96063 NA
2237cc 2.2 4 86-89 4YEC   3Y, Z21 34 96065 NA
2362cc 2.4 4 01-07 2AZFE 02-07 Camry, 01-07 Highlander, 04-05 Rav 4, 02-07 Solara. Remove counter balance shaft from old unit and put on new unit.   42 96094  
2366cc 2.4 4 3/82-84-1/2 22R 81-3/82 Celica, Corona, Pickup   43 96063 NA
2.4 4 84-1/2 - 95 22R, 22RE, 22REC, 22RETC 3/82-95 Celica, Pickup, 4Runner and Corona. Bearings packaged for engines made after February '82.   43 96064 NA
2438cc 2.4 4 90-04 2TZFE, 2TZFZE, 2RZFE 90-97 Previa, 95-97 Previa supercharged, 95-04 Tacoma RZ 45 96084 NA
2507cc 2.4 V6 88-91 2VZFE 88-91 Camry, 90-91 Lexus ES250.   35 96070 NA
2563cc 2.6 6 71-80 4M, 4ME 73-76 Corona MKII, 78-80 Cressida, 71-72 Crown and 79-80 Supra.   64 96066 NA
2693cc 2.7 4 94-05 3RZFE 94-05 Tacoma, 4Runner and T100. RZ 49 96083 NA
2759cc 2.8 6 81-84 5ME, 5MGE 81-7/84 Cressida and Supra 2M, 4M 65 96066 NA
2.8 6 84-88 5MGE 8/84-88 Cressida and Supra 2M, 4M 65 96067 NA
2954cc 3.0 6 86-92 7MGE, 7MGTE 89-92 Cressida, 86-92 Supra and 87-92 Supra turbo. 6M, 7M 56 96078 NA
2959cc 3.0 V6 88-95 3VZE 88-95 Pickup, 4Runner and T100. Crankshaft neck length is 2.750".   40 96068 NA
3.0 V6 92-93 3VZFE 92-93 Camry and Lexus ES300. Crankshaft neck length is 2.525".   44 96069 NA
2995cc 3.0 V6 94-06 1MZFE 94-06 Camry, Avalon, Sienna, Solara and 94-03 Lexus ES300, RX300.   43 96071 NA
2997cc 3.0 6 93-98 2JZGE, 2JZGTE 95-98 Supra, Supra turbo, 92-97 Lexus GS300 and SC300.     96090  
3310cc 3.3 V6 03-07 3MZFE 03-07 Camry, Highlander, Sienna and Lexus RX330 and ES330.     96096  
3378cc 3.4 V6 95-04 5VZFE 95-98 T100, 95-04 Tacoma, Tundra and 4Runner - VIN code N & V.   44 96087 NA
3968cc 4.0 V8 90-00 1UZFE 90-00 Lexus GS400, LS400   60 96091 NA
4293cc 4.3 V8 01-07 3UZFE Lexus LS430 and GS430.     96092  
4663cc 4.7 V8 98-07 2UZFE Lexus 98-07 LX470, 03-07 GX470. Toyota 03-07 4-Runner, 98-07 Landcruiser, 01-07 Sequoia, 99-07 Tundra.     96093  
VOLKSWAGEN                
  1.8   98-05 AEB, AUG, AWM DOHC 20V Turbo     75003  
2792cc 2.8 V6 92-97 VR6 92-95 Jetta, Golf GTI, Passat GLX, 92-94 Corrado SLC reluctor ring 4.328" D21B, I438 48 75001  
2.8 V6 92-97 VR6 92-95 Jetta,Golf GTI, Passat GLX,92-94 Corrado SLC reluctor ring 3.856" D21B, I438 48 75002